Differences

This shows you the differences between two versions of the page.

--- en:registrierform [2022/03/30 17:12] – [Registrierwerkzeuge] onyxadmin
+++ en:registrierform [2024/03/14 14:54] (current) – onyxadmin
@@ Line 1: / Line 1: @@
+====== Panel Surface Registration 3D ======
-====== Registration Form ======
 ----
 Various workflows require the mutual alignment of 3D objects, e.g. on surface features. This also includes the registration of surfaces extracted from volume data.\\
-For this purpose, a registration form can be used at different places, which provides different tools for feature extraction and surface alignment.\
+For this purpose, a registration form can be used at different places, which provides different tools for feature extraction and surface alignment. Currently, the object preparation window can be used for the modules
-Currently, the object preparation window can be used for the modules
    * [[combine_3d|Combine 3D]]
@@ Line 11: / Line 9: @@
    * [[tadmatch_3d|TADmatch]]
    * [[inspect_3d|Inspect 3D]]
-   * [Articulate 3D]
+   * [[articulate_3d|Articulate 3D]]
 When the form is opened, the two objects or object groups to be registered must be selected in an object list window.
@@ Line 19: / Line 17: @@
 =====User Interface =====
-{{:ui_fusion.png?761&direct|}}
+[[fusion1|{{:ui_fusion.png?761&direct|}}]]
 The basic idea is to register the objects of the left view to the object of the middle view. The right view shows the preview of the currently achieved registration.\\
@@ Line 34: / Line 33: @@
 Various registration tools are provided. Press [Apply] to return the realigned subobject (left) to the parent window.
-==== Punktpaarbasierte Registrierung ====
+==== Point Pair Based Registration ====
 [[fusion1#points|{{:ui_fusion_pts.png?&direct}}]]
-  * Punktpaare auf Quell- und Zielobjekt setzen, welche nach der Registrierung möglichst übereinander liegen sollen
+  * Set point pairs on source and target object, which should be on top of each other after registration if possible.
-  * Die Punkte werden in der richtigen Reihenfolge mit Rechtsklick auf die Objekte gesetzt. Punkte mit derselben Farbe werden im Ergebnis möglichst übereinander gelegt
+  * Set the points in the correct order by right-clicking on the objects. Points with the same color are placed on top of each other in the result if possible
-  * Optional kann die umliegende Oberfläche der Punkte in einem einstellbaren Radius beachtet werden
+  * Optionally the surrounding surface of the points can be observed in an adjustable radius
-==== Topologiebasierte Registrierung ====
+==== Topology-based registration ====
 [[fusion1#mark area|{{:ui_fusion_mrk.png}}]]
-  * Mit einem Pinselwerkzeug können Oberflächenbereiche auf Objekten markiert werden
+  * A brush tool can be used to mark surface areas on objects
-  * Sind Bereiche grün markiert, werden nur diese Bereiche für die Registrierung verwendet.
+  * If areas are marked in green, only these areas are used for registration
-  * Mit der linken Maustaste können Bereiche markiert werden. Bei gehaltener [STRG] Taste werden die Bereiche wieder von der Markierung abgezogen.
+  * Areas can be marked with the left mouse button. If the [CTRL] key is held down, the areas are removed from the marking again
-  * Optional kann der Radius des Werkzeuges eingestellt werden
+  * Optionally, the radius of the tool can be set
-  * Sind keine Bereiche grün markiert, werden alle Oberflächen verwendet
+  * If no areas are marked green, all surfaces are used
-==== Magnetwerkzeug ====
+==== Magnet====
 [[fusion1#magnet|{{:ui_fusion_mag.png?&direct}}]]
-  * Quell- und Zielobjekt an einer bestimmten Stelle aufeinanderziehen
+  * Drag the source and target objects to each other at a specific point.
-  * In der Vorschauansicht (rechts) mit Rechtsklick einen Punkt auf dem Quellobjekt auswählen, der sich zum nächstgelegenen Punkt auf der Oberfläche des Zielobjektes bewegen soll
+  * In the preview view (right), right-click to select a point on the source object to move to the closest point on the surface of the target object.
 ==== Navigator====
@@ Line 64: / Line 63: @@
 [[fusion1#navigator|{{:ui_fusion_nav.png?&direct}}]]
-  * Das Quellobjekt im Vorschaufenster per 3D Navigator manuell bewegen.
+  * The 3D object to be registered can be moved manually relative to the target object via 3D Navigator in the right preview window.
+\\
+==== Distance measurement ====
+{{:ui_fusion_dm.png?761&direct}}
+When the [Distance Measurement] icon button is activated, the vertex-to-vertex distance between the two surfaces is calculated. If this is below 0.5mm, then the related surface areas are colored green in the right panel. The distance value 0.5mm can be adjusted via an INI entry.\\
+At the same time the local distance value can be displayed with a mouse click at each surface point.\\
+//Note//: The calculation of the surface distances and thus the coloring can take some seconds depending on the graphics performance. The local detection of distance values remains unaffected by this.\
+\\