en:positive_aligner
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
en:positive_aligner [2023/02/15 09:01] – [Positive Aligners] onyxadmin | en:positive_aligner [2023/05/31 07:45] (current) – onyxadmin | ||
---|---|---|---|
Line 2: | Line 2: | ||
---- | ---- | ||
- | <WRAP center todo 100%> | + | Since 2022, various manufacturers (e.g. [[http:// |
+ | \\ | ||
+ | <WRAP center | ||
This functionality is still in development and only available as preview version for testing. Please verify all results and models exported from the planning as usual. | This functionality is still in development and only available as preview version for testing. Please verify all results and models exported from the planning as usual. | ||
</ | </ | ||
Line 12: | Line 14: | ||
[[trimline_pm# | [[trimline_pm# | ||
\\ | \\ | ||
- | This line is now part of the project, will be automatically adapted when switching to other steps, and is also visualized on the models when switching to the 3D export. | + | This line is now part of the project, will be automatically adapted when switching to other steps, and is also visualized on the models when switching to the 3D export.\\ |
+ | |||
+ | <WRAP nicebox orange center important> | ||
+ | **Note:** The [[trimline_pm|Trim Line panel]] in module [[: | ||
+ | </ | ||
===== 3D Export ===== | ===== 3D Export ===== | ||
- | In the 3D Export window, please set the following configuration and save this as a separate export | + | As of Release 3.2.195, there is a separate export |
- | * Trim the model with the planes down to the height of the trimline | + | {{: |
- | * Minimum Blockout is required (0.5 mm) | + | |
- | * Labeling positive onto the teeth | + | |
- | * No print-preprocessing activated | + | |
- | In the bottom panel for the serial export, a new option " | + | The required Expot settings can be made in the window. Optionally, the rail thickness can also be modified in proportion to the planned range of motion.\\ |
- | According to first feedback the thickness should be set to something around 0.4-0.6 mm. The rounding can currently only be used for trays thicker than 0.5-0.6 mm, depending on the model. Please note that the settings are currently not saved and always reset tothe default values. | + | {{: |
- | ===== Additional objects ===== | + | //Note//: \\ |
- | + | According | |
- | How 3D objects should be added to the arch/s or to the aligner/s can be indirectly controlled by the name of the additional object: | + | The possibility of adding support material is intended only as a fallback option for printers whose print preparation does not provide a suitable option for this.\\ |
- | + | ||
- | * if the name contains the term " | + | |
- | * if the name contains | + | |
- | * otherwise | + | |
- | + | ||
- | ---- | + | |
+ | <WRAP nicebox orange center important> | ||
+ | **Note:** The serial 3D export of positive aligners additionally requires the activation of [[bitesplint_3d|module Bite Splint 3D]], since its calculation algorithms are used. | ||
+ | </ | ||
+ | \\ | ||
- | ^ Note for Testing | ||
- | | This version is available as a preview to allow first tests with the material and is not part of the official product. The user interface and workflows will be greatly reworked and enhanced with more options in the official release |
en/positive_aligner.1676448076.txt.gz · Last modified: 2023/02/15 09:01 by onyxadmin